The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
This great article following next on the subject of How to Install a Bathtub is totally engaging. Don't skip it.
Installing a bath tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is additionally a moderately hard task. If the old bathtub is conveniently easily accessible, the task can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and set in the new one. Make sure you have actually certified yourself for the work and also are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is far better to think about employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This post will certainly assist you install a new tub in your bathroom if you have actually already acquired a brand-new bathtub and do not require to change the setup of your previous water supply pipelines.
Your devices as well as material list must comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
Before moving on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the tap ends first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using both wooden boards under its feet, put the bath tub in the needed setting. The wooden boards are useful in uniformly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the bath tub till the spirit level reads degree.
To mount taps, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water system and examine all joints and brand-new pipework for leakages and tighten them if essential. Fill up the bath tub and likewise examine the overflow outlet as well as the regular electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub ought to wait till the bath tub has actually been utilized a minimum of once as this will settle it right into its last position.
Preparing for the Installment
First of all, the supporting frame provided with the bathroom should be fitted (if required) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you use all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to split an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about complications with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and also cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very occupied with Installing A Bathtub and I'm hoping you enjoyed reading our entry. Sharing is good. Helping others is fun. Many thanks for your time. Visit again soon.
Reliable repairs? Dial. Report this page